Below Nav Bar

Collapse

Timing chain bolt tension

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • bear
    Junior Member
    • Aug 2008
    • 11
    #1

    Timing chain bolt tension

    Got the NP apart to do the chain guide, the old one looked fine but I will replaced it anyway.
    My question is, does anyone know what tension the two bolts holding it on should be ?????
    Tags: None
  • dbdb
    Senior Member
    • Aug 2008
    • 330
    • Adelaide Hills
    #2
    I just did mine up tight as I could without stripping the thread. Not too scientific, sorry.

    Richard
    14 NW GLX-R automatic, dual battery, Icom 440 UHF, redarc tow pro, Bushskinz bash plates, light bar, Dobinsons suspension, HPD front mount intercooler, ARB bull bar and other stuff.
    04 NP GLX now gone

    Pajero Service Manual link

    Comment

    • Phil
      Valued Member
      • Aug 2008
      • 801
      • Sydney
      #3
      I would say 15-20 Nm max.

      They are only 12mm bolt heads that are just holding the guide plate in place.

      Phil.
      MY05 NP DiD Auto Platinum. Custom scratches. ARB bar & 12000lbs winch. Maxxis Bighorns. BushSkinz Bash plates & slidders. TJM auto guard. Gear box, trans & diff breathers. Rhino racks & Pod. Awning with LED. Dual batteries. HID Narva 225's. Airtec snorkel. 2" Lovell/Bilstein lift. GME TX3500. Wetseat covers. Pioneer BT deck. Cargo barrier. Beaudesert exhaust. Rear storage & CF80. ARB onboard air. NS 18s for the black top, 80L LRA tank. HPD Catch Can. HPD Intercooler.

      Comment

      • Muzza
        Valued Member
        • Jul 2007
        • 858
        • Nsw
        #4
        20Nm

        Muzza
        Muzza
        2014 NW VRX , Alloy ECB bar, Poly air bags, EGR fixed. EDS scan gauge, lockup mate.
        2003 NP DID GLS retired and gone to a good home
        2007 21' Lotus spirit caravan

        LH Torana

        Comment

        • sharkcaver
          "2000"+ Valued Contributor
          • May 2009
          • 6270
          • Perth
          #5
          All the literature I could find on this (which was very little, stated 33+/- 3 Nm.

          Didn't post before as I wanted to see what others stated and 33 seems low to me (but I work in hundreds of Nm's daily, 33 seems like a sparrows fa*t)

          Going by the other replies, it should be about right then I guess.

          Shane.
          MY16 NX GLX5 with just a few bits added. MY14 D-max spacecab, also with a few bits added.

          My Journeys

          Comment

          • gjh1967
            Valued Member
            • Dec 2007
            • 484
            • Lake Macquarie
            #6
            Hi Bear

            33 +/- 3Nm from the Mitsu factory workshop manual

            Cheers
            Glenn
            2003 NP 3.2 DI-D LWB 5spd-DVD Entertainment unit-Narva 175 blue's-Side Steps-Uniden UHO15SX-Garmin GPS16 and Oziexplorer-ARB On Board air-Polyairs-Airtek Snorkel-Khumo KL78's-Headrest DVD players- Ironman Lift kit- 12000lb winch- Dual Batteries - Redarc isolator-Bushskinz intercooler guard.

            Comment

            • bear
              Junior Member
              • Aug 2008
              • 11
              #7
              Did the reserch

              HEAD MARK "7"
              M8- 1.25- 20 ? 4 N⋅m (15 ? 3 ft-lb)

              2006
              MITSUBISHI
              MONTERO
              SERVICE MANUAL
              V1
              hope this is right because thats what I did
              Thanks every one for your input.

              Comment

              Previous template Next

              Matched content

              Collapse
              Working...
              X