Pajero 4WD Club of Victoria Public Forum Pajero 4WD Club of Victoria Public Forum

Go Back   Pajero 4WD Club of Victoria Public Forum > Commercial Advertisers > Commercial Advertisers > Autophix Australia

Autophix Australia We'll keep you moving !

Reply
 
Thread Tools Display Modes
  #1  
Old 30-08-20
Autophix Australia Autophix Australia is offline
Junior Member
 
Join Date: Aug 2020
Posts: 1
Default Hi to all !

Just an introduction here and great to be part of your community.
Autophix Australia is based in Melbourne, Victoria. A passion for automotive and 4wd and a career in the industry for over 20 years has led company director Trevor Ryan to make fault finding for your vehicle an easy DIY task.

“I was caught in the middle of Australia and my car went into limp mode. I had no way of checking what was wrong”

After having a major vehicle malfunction in the middle of Australia with no easy tool to diagnose the problem, Trev went on a quest to bring a DIY diagnostic tool to the Australian Automotive industry.
The Autophix Australia range of OBDII scanning tools has now made this a reality. With a variety of features available, there is a unit to suit all experience levels. From wireless Bluetooth scanners to fully-fledged workshop grade units, our product range will have a model to suit you.
Autophix OBD2 Scanners scan through all available ECU protocols in most vehicles built after 1996.
You can order through our website and be assured of prompt service
https://autophixaustralia.com.au/

Last edited by Autophix Australia; 30-08-20 at 05:49 PM.
Reply With Quote
  #2  
Old 30-08-20
nj swb's Avatar
nj swb nj swb is online now
Resident
 
Join Date: Jun 2007
Location: Adelaide
Posts: 6,385
Default

Hello Autophix, welcome to the forum.

In the Mitsubishi world, most functions beyond standard OBDII stuff requires a Mitsubishi MUT-3, or something compatible.

There are a range of MUT-3 clones that (anecdotally) may or may not work, and a variety of other devices that fall between the basic OBDII device and the genuine MUT-3 (in terms of what they can and cannot do).

With this in mind, can you recommend a model from your range that will do more for our typical Mitsubishi-owning forum member than the ubiquitous code scanner / monitor?
__________________
NT Platinum. DiD Auto with 265/70R17 Toyo MT, Lift, Lockers, Lockup Mate, Low range reduction, LRA Aux tank, bull bar, winch, lots of touring stuff. Flappy paddles. MMCS is gone!

Project: NJ SWB. 285/75R16 ST Maxx, 2" OME suspension, 2" body lift, ARB 110, 120l tank, bullbar, scratches, no major dents. Fully engineered in SA. NW DiD & auto in place - a long way to go....

Scorpro Explorer Box
Reply With Quote
  #3  
Old 31-08-20
GHendo's Avatar
GHendo GHendo is offline
Valued Member
 
Join Date: Mar 2012
Location: Northern NSW
Posts: 4,351
Default

Quote:
Originally Posted by nj swb View Post
Hello Autophix, welcome to the forum. ... can you recommend a model from your range that will do more for our typical Mitsubishi-owning forum member than the ubiquitous code scanner / monitor?
x2

Geoff
__________________
03 NP Manual Di-D Exceed, 2" lift, Dobinsons Springs, Lovells Shocks, ORU Winch, ARB Bullbar, Scott's Rods 3" Exhaust, ARB Compressor, Rear Air Locker, Cooper S/T Maxx, Hella Rallye 4000 S/Lights, Pioneer AVH-X5850BT DVD/Tuner w/- Reversing Camera, Sensa Tyre monitor, Uniden UH8080NB UHF, Rhino Platform Roof Rack, Hema HN-7 GPS, Engine Watchdog, CouplerTec, CTEK D250S DC-DC Charger, Snorkel, Towbar.
Reply With Quote
  #4  
Old 31-08-20
stumagoo stumagoo is online now
Valued Member
 
Join Date: Jun 2014
Location: Perth WA S.O.R
Posts: 1,754
Default

Quote:
Originally Posted by nj swb View Post
Hello Autophix, welcome to the forum.

In the Mitsubishi world, most functions beyond standard OBDII stuff requires a Mitsubishi MUT-3, or something compatible.

There are a range of MUT-3 clones that (anecdotally) may or may not work, and a variety of other devices that fall between the basic OBDII device and the genuine MUT-3 (in terms of what they can and cannot do).

With this in mind, can you recommend a model from your range that will do more for our typical Mitsubishi-owning forum member than the ubiquitous code scanner / monitor?

I suspect this is originally a US based item - over there OBD2 is mandatory from 96 or so on.

here and the rest of the world Pajero's only went OBD2 on NP3.8's and newer (NS diesel I believe was the diesel change over) Prior to that its all Mutt protocol and no OBD2 scanner works.

Unless this is a scanner like big foxconn or snapon that support OBD1 (proprietry protocols) units it is probably only OBD2 compliant and as such will only work on the newer vehicles.
__________________
1994 NJ 3.0 now with a 2000NL 3.5 engine and driveline, 2.5 catback, 32" MT Deegan 38's, 1" body lift, front diff drop with front tension rods indexed and cranked an 3", 3" on the rear coils
*** retired to the big wrecking yard in the sky***
1998 NL blisterside, 285.75.16's on -22 rims 3" suspension lift, Custom Bull bar, winch install, custom front control arms, NJ GLS flares and some camping gear in the back

.... and 1990 Nissan Z32 300zx for on road shenanigans
.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time now is 07:09 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.