Scanguage or Ultraguage

[Pixie_au]

Do any or all of these allow clearing of error codes?

[Dicko1]

Do any or all of these allow clearing of error codes?

Yes.

[Pixie_au]

Thanks man!

[craigs_r75]

Programming

Hi m_and_m,

I have received the Ultraguage but am getting an error for the Auto Temp guage that I have setup.

I presume that it is something minor

I have redefined M guage 5 with
Tdata = 07E12102000000
Mtch = 210000
Rpos = 1008
Tctrl = 93
Rctrl = 31
X = :0001 /: 0001 +:FFD8
Output = 0
Ave = 0
Left/Right = 0

I have put it with KPH on page 6. The KPH does not indicate ERR but AFT does

I would appreciate your help

I thought I would just have ATF and KPH on page 6 and Eng temp and Volts on page 7. If you have a recommended better arrangement I would like to hear about that also.

Regards Craig Shaw 0473737329

[nj swb]

Hi m_and_m,

I have received the Ultraguage but am getting an error for the Auto Temp guage that I have setup.

I presume that it is something minor

I have redefined M guage 5 with
Tdata = 07E12102000000
Mtch = 210000
Rpos = 1008
Tctrl = 93
Rctrl = 31
X = :0001 /: 0001 +:FFD8
Output = 0
Ave = 0
Left/Right = 0

I have put it with KPH on page 6. The KPH does not indicate ERR but AFT does

I would appreciate your help

I thought I would just have ATF and KPH on page 6 and Eng temp and Volts on page 7. If you have a recommended better arrangement I would like to hear about that also.

Hi Craig,

In the above post, you have "Left/Right" = 0. Others (such as this post) show it set to 30.

I have no idea what this number means, or if its your problem, but give it a go.

Also, you have your offset as FFD8 - if your NT is a diesel you should be using FFCE. If you have a petrol you have the Jatco transmission, and I'm not sure which is the correct offset.

[craigs_r75]

I'll go and give it a try

[craigs_r75]

No luck, didn't change anything. Regards Craig

[craigs_r75]

Sorry missed your comment about FFCE, that is probably problem, will go and try again

[geopaj]

I know it sounds silly but have you got the ignition on (not just accessories)? With just accessories on, mine will show all readings except trans temp - which displays an error message.

[craigs_r75]

Changing FFD8 to FFCE still doesn't work, but previously it went to ERR as soon as you went onto page, now it shows nothing for 5 seconds before giving ERR.

[craigs_r75]

With engine running I get the ERR

[2bad4u]

Hi m_and_m,

I have received the Ultraguage but am getting an error for the Auto Temp guage that I have setup.

I presume that it is something minor

I have redefined M guage 5 with
Tdata = 07E12102000000
Mtch = 210000
Rpos = 1008
Tctrl = 93
Rctrl = 31
X = :0001 /: 0001 +:FFD8
Output = 0
Ave = 0
Left/Right = 0

I have put it with KPH on page 6. The KPH does not indicate ERR but AFT does

I would appreciate your help

I thought I would just have ATF and KPH on page 6 and Eng temp and Volts on page 7. If you have a recommended better arrangement I would like to hear about that also.

Regards Craig Shaw 0473737329

You should have the following:

TCtrl = 92
RCtrl = 10
+ FFCE
Left/Roght = 30

.

[2bad4u]

Here is what you should be using...

[craigs_r75]

Still no luck unfortunately.

My Pajero is a 2010 NT, with 3.2 Diesel, and 5 speed Auto.

[craigs_r75]

It appears to be a slight difference as to which values should be given. I guess this is because of the CPU and transmission. Is there a document or link to where I can work out what is required.

I started with the info on the scanguage site, it only gives one set of values for Pajero which I adapted for Ultraguage. The Ultraguage user guide shows some trouble shooting techniques which I could possibly use but that is hard work if someone has already done it.

Does anyone have the same Pagero (2010 NT 3.2 5 speed) which they know the values work on? Then if mine doesn't work, maybe I have a problem in the vehicle itself.

The Ultraguage seems to be working correctly and other guages (kph, engine temp etc) are working when I drive the vehicle.