Pajero 4WD Club of Victoria Public Forum Pajero 4WD Club of Victoria Public Forum

Go Back   Pajero 4WD Club of Victoria Public Forum > Vehicles > Pajero Sport > Pajero Sport QE 2015 - 2019

Pajero Sport QE 2015 - 2019 The Pajero Sport new to Oz

Reply
 
Thread Tools Display Modes
  #51  
Old 1 Week Ago
old Jack's Avatar
old Jack old Jack is online now
Administrator
 
Join Date: Jun 2011
Location: Adelaide, South Australia.
Posts: 7,829
Default

Seems like a good result but the rear coils will settle about 5mm to 10mm from where they are when first fitted.
You should notice the difference even more when driving both hitched and unhitched, there should be less wallowing and pitching of the rear suspension.

Once the WDH is fitted and setup correctly, only to return the front ride height measurements back to the pre-hitched measurements then the whole setup should tow and ride much better.

Hopefully this is good enough and you do not need to go down the airbag route.

OJ.
__________________
2011 PB Base White Auto, Smartbar, Cooper STMaxx LT235/85R-16,TPMS, HR TB, 3 x Bushskinz, front +40mm Dobinson , rear +50mm EHDVR Lovells, Dobinson MT struts and shockers, Peddars 5899 cone springs, Windcheater rack, GME UHF, Custom alloy drawer system inc. 30lt Engel & 2 x 30 AH LiFePo batteries + elec controls, Tailgate hi-lift/long struts, Phillips +100 LB & HB, Lightforce 20" single row driving beam LED lightbar, Scanguage II.
MM4x4 Auto Mate, Serial No 1 .
Reply With Quote
  #52  
Old 4 Days Ago
josmond josmond is offline
Junior Member
 
Join Date: Sep 2020
Location: QUAKERS HILL
Posts: 12
Default

So I hooked up the WDH today, just did a quick test and didn't dial it in precisely, but rough measurements (also car was on a bit of a sideways angle, need to do again on fully flat):

Front wheel:
No Van: 515
Van (no WDH): 525
Van (WDH): 520

Back wheel:
No Van: 600
Van (no WDH): 560
Van (WDH): 565

So reduce the front lift from 10mm to 5mm.
My socket wrench didn't fit in the provided socket for tightening the chains, so that was just by hand tightening, I'll go to Bunnings and get a proper socket for it which should hopefully allow me to tight properly and bring the front back down the extra 5mm.

What's the recommendation with the Anderson WDH for reversing, tight maneuvering, or rough roads etc?
To get to my parking spot on the drive way, i do have a bit where the car and van are at quiet different angles going up a slope to the levelish ground at the top. Hoping that I don't need to disconnect to get up over that.
Reply With Quote
  #53  
Old 4 Days Ago
Dicko1's Avatar
Dicko1 Dicko1 is offline
Valued Member
 
Join Date: Dec 2014
Location: Cairns, FNQ
Posts: 5,693
Default

Quote:
Originally Posted by josmond View Post
So I hooked up the WDH today, just did a quick test and didn't dial it in precisely, but rough measurements (also car was on a bit of a sideways angle, need to do again on fully flat):

Front wheel:
No Van: 515
Van (no WDH): 525
Van (WDH): 520

Back wheel:
No Van: 600
Van (no WDH): 560
Van (WDH): 565

So reduce the front lift from 10mm to 5mm.
My socket wrench didn't fit in the provided socket for tightening the chains, so that was just by hand tightening, I'll go to Bunnings and get a proper socket for it which should hopefully allow me to tight properly and bring the front back down the extra 5mm.

What's the recommendation with the Anderson WDH for reversing, tight maneuvering, or rough roads etc?
To get to my parking spot on the drive way, i do have a bit where the car and van are at quiet different angles going up a slope to the levelish ground at the top. Hoping that I don't need to disconnect to get up over that.



What are the actual weights of your van from the weighbridge? Tare when empty and fully loaded.
__________________
Dicko FNQ


2014 NW with all the usual stuff plus more.
Having lots of friends on facebook is the same as having lots of money in monopoly...both meaningless.

.

Telegraph X camper
Reply With Quote
  #54  
Old 4 Days Ago
old Jack's Avatar
old Jack old Jack is online now
Administrator
 
Join Date: Jun 2011
Location: Adelaide, South Australia.
Posts: 7,829
Default

Quote:
Originally Posted by josmond View Post
So I hooked up the WDH today, just did a quick test and didn't dial it in precisely, but rough measurements (also car was on a bit of a sideways angle, need to do again on fully flat):

Front wheel:
No Van: 515
Van (no WDH): 525
Van (WDH): 520

Back wheel:
No Van: 600
Van (no WDH): 560
Van (WDH): 565

So reduce the front lift from 10mm to 5mm.
My socket wrench didn't fit in the provided socket for tightening the chains, so that was just by hand tightening, I'll go to Bunnings and get a proper socket for it which should hopefully allow me to tight properly and bring the front back down the extra 5mm.

What's the recommendation with the Anderson WDH for reversing, tight maneuvering, or rough roads etc?
To get to my parking spot on the drive way, i do have a bit where the car and van are at quiet different angles going up a slope to the levelish ground at the top. Hoping that I don't need to disconnect to get up over that.
This is all progressing Josh

Once you have the Anderson hitch set up correctly it will be interesting to hear how your towing experience has changed.

No need to disconnect the Anderson WDH when reversing or when going through drains, as long as the trailer movement is within the articulation range of the 50mm ball. This is one of the major benefits of using an Anderson WDH.
https://andersenhitches.com/Catalog/...ion-hitch.aspx

OJ.
__________________
2011 PB Base White Auto, Smartbar, Cooper STMaxx LT235/85R-16,TPMS, HR TB, 3 x Bushskinz, front +40mm Dobinson , rear +50mm EHDVR Lovells, Dobinson MT struts and shockers, Peddars 5899 cone springs, Windcheater rack, GME UHF, Custom alloy drawer system inc. 30lt Engel & 2 x 30 AH LiFePo batteries + elec controls, Tailgate hi-lift/long struts, Phillips +100 LB & HB, Lightforce 20" single row driving beam LED lightbar, Scanguage II.
MM4x4 Auto Mate, Serial No 1 .
Reply With Quote
  #55  
Old 4 Days Ago
orthodoxs orthodoxs is offline
Member
 
Join Date: Mar 2018
Location: Darwin
Posts: 54
Default

Quote:
Originally Posted by josmond View Post
S
My socket wrench didn't fit in the provided socket for tightening the chains, so that was just by hand tightening, I'll go to Bunnings and get a proper socket for it which should hopefully allow me to tight properly and bring the front back down the extra 5mm.

What's the recommendation with the Anderson WDH for reversing, tight maneuvering, or rough roads etc?
To get to my parking spot on the drive way, i do have a bit where the car and van are at quiet different angles going up a slope to the levelish ground at the top. Hoping that I don't need to disconnect to get up over that.
Like OJ said, you dont have to remove for reversing or inclines. I haven't used one but, after assembling it, lifting the A frame with the jockey and then tigtening the chains may be the right way to go, instead of cranking it with full load on the chains. once levelled users detach the triangular plate each time they need to decouple leaving the chains and triangular plate attached to the frame. You must be aware of this by now as there are many videos on U tube.
How much did you get it for and where from? pls share your opinions as i may need to change mine from the HR type tension bars and chain as i had to move the A frame chain attachment clamps more towards the caravan ( now the chains are not Vertical and become excessively tight when turning.)
P.S: If you detach the plate while the tow is at an angle to the caravan after parking, it may need a small trick to get it back on or you will have to reverse the tow back in the same angle.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Towing large forward fold camper trailer offroad - ok? secateurs Camping /Caravan Parks/ Campers 8 03-12-17 01:10 PM
Towing a 2.5t caravan with original suspension karlZ Generation 4-2 Pajero 16 25-10-16 03:54 PM
Suspension suggestions for Caravan Towing netorius77 Generation 3 Pajero 24 09-11-11 09:57 AM
Advice on towing a large caravan Rod-in-ACT Generation 3 Pajero 58 14-01-11 10:48 AM


All times are GMT +10. The time now is 12:18 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.