Pajero 4WD Club of Victoria Public Forum Pajero 4WD Club of Victoria Public Forum

Go Back   Pajero 4WD Club of Victoria Public Forum > Search Forums

Showing results 1 to 25 of 500
Search took 0.03 seconds.
Search: Posts Made By: erad
Forum: Bolted on bits, factory and aftermarket accessories 2 Days Ago
Replies: 3
Views: 474
Posted By erad
I fitted a genuine MM bullbar from a NS Model to...

I fitted a genuine MM bullbar from a NS Model to my NW Pajero no problems at all. NS is the earliest model you can use - the NM/NP model bars will fit but the heaflights are different.
Forum: Mechanical 2 Days Ago
Replies: 6
Views: 309
Posted By erad
Measuring the pulley offset accurately is...

Measuring the pulley offset accurately is difficult but you should be able to improve it at least by adding a washer behind the pulley. Probably there was a spacer there in the first place. Remember...
Forum: Mechanical 5 Days Ago
Replies: 10
Views: 196
Posted By erad
Sorry - I don't know any aftermarket setups but I...

Sorry - I don't know any aftermarket setups but I am sure there will be some. Another thing you would need (hopefully part of the kit you get) would be limit switches for the clutch and brake pedals
Forum: Mechanical 5 Days Ago
Replies: 10
Views: 196
Posted By erad
Cruise control requires a vacuum source to...

Cruise control requires a vacuum source to operate the system. The V6 engine has vacuum from normal throttle operation. A diesel doesn't have that so you would need to get a separate vacuum pump....
Forum: Generation 4-3 Pajero 5 Days Ago
Replies: 58
Views: 1,449
Posted By erad
I occasionally get a flat battery in my NW...

I occasionally get a flat battery in my NW Pajero. My car gets used intermittently - Where possible I won't use it for short runs and use my wife's Outlander as a shopping cart.

I do have the...
Forum: Generation 3 Pajero 6 Days Ago
Replies: 11
Views: 882
Posted By erad
Have you swapped the front and rear diffs? They...

Have you swapped the front and rear diffs? They will be different ratios.
Forum: General Info 1 Week Ago
Replies: 7
Views: 352
Posted By erad
Everyone these days is praising the electric car,...

Everyone these days is praising the electric car, and mostly with good reason. The main virtue of an electric car is lack of pollution - at least in the city where most of them will be anyway. Forget...
Forum: Generation 4-1 Pajero 1 Week Ago
Replies: 2
Views: 161
Posted By erad
Get a couple of keys done while you are at it....

Get a couple of keys done while you are at it. Put an uncoded key somewhere under the car so you can get in if you lose your main key(s). Then hide a spare (coded) key somewhere inside the car. At...
Forum: Generation 2 Pajero 1 Week Ago
Replies: 11
Views: 471
Posted By erad
Radio aerial wiring? (my NL Escape had a switch...

Radio aerial wiring? (my NL Escape had a switch for the aerial in that console)
Forum: General Info 1 Week Ago
Replies: 7
Views: 352
Posted By erad
The technology to put electric motors of...

The technology to put electric motors of virtually any size into a vehicle already exists - look at diesel electric locomotives. The problem is that you need to get power to the brutes where you need...
Forum: Generation 4-1 Pajero 1 Week Ago
Replies: 35
Views: 1,499
Posted By erad
Tomo88: If you are missing some or all of the...

Tomo88:
If you are missing some or all of the fan shroud, this could well be the cause of some overheating. Without the shroud, the fan can draw air in from behind the radiator, thereby not getting...
Forum: Generation 4-1 Pajero 1 Week Ago
Replies: 35
Views: 1,499
Posted By erad
I have been watching this thread with interest....

I have been watching this thread with interest. To my way of thinking, everyone is focusing on the transmission, but there is still a fault with the cooling system. Yes - a slipping torque converter...
Forum: Generation 4-3 Pajero 1 Week Ago
Replies: 23
Views: 3,180
Posted By erad
In short, no. Even if you get some reduction in...

In short, no. Even if you get some reduction in free play, this will be for a limited time.
Forum: Mechanical 1 Week Ago
Replies: 6
Views: 309
Posted By erad
Maybe you are tightening the belts too tight and...

Maybe you are tightening the belts too tight and they are wearing? How much slack do you have in the longest free section of belt?
Forum: Bolted on bits, factory and aftermarket accessories 1 Week Ago
Replies: 3
Views: 290
Posted By erad
I haven't had directly this bar, but I have a...

I haven't had directly this bar, but I have a similar bar on my wife's ZJ Outlander. It is 304 stainless steel, 3" tubing - looks far more solid that the standard MM nudge bar (but I doubt that it is...
Forum: Generation 4-3 Pajero 2 Weeks Ago
Replies: 21
Views: 1,103
Posted By erad
Is the vehicle under warranty?A dealers...

Is the vehicle under warranty?A dealers presumably because it is probably out of MMAL warranty. IF there is a warranty associated with this car, report the incident to the dealer IN WRITING. Even if...
Forum: Mechanical 2 Weeks Ago
Replies: 7
Views: 297
Posted By erad
If you search through this forum for overheating...

If you search through this forum for overheating problems, probably 90% or more of them started out like you, but ultimately finished up either replacing or repairing the fan clutch. Just because the...
Forum: Generation 2 Pajero 3 Weeks Ago
Replies: 2
Views: 157
Posted By erad
The starter motor on the diesels is on the other...

The starter motor on the diesels is on the other side, so the petrol/diesel swap is not simple (if at all). In addition, the ratios are different.
Forum: Generation 2 Pajero 3 Weeks Ago
Replies: 15
Views: 568
Posted By erad
If the threaded hole is not properly cleaned out,...

If the threaded hole is not properly cleaned out, the bolt could bottom out - either on crud at the bottom of the hole, or on a fouled thread. This would give the "correct" tightening torque, but...
Forum: Generation 4-3 Pajero 3 Weeks Ago
Replies: 3
Views: 385
Posted By erad
My ever fading memory tells me that the mounting...

My ever fading memory tells me that the mounting brackets for my bullbar (a genuine MM bar to suit a NS, fitted to my NW Pajero) were bent from new ie the mounting onto the bar was wider than the...
Forum: Generation 4-3 Pajero 3 Weeks Ago
Replies: 4
Views: 334
Posted By erad
Modern highways often have measured 5 km sections...

Modern highways often have measured 5 km sections of road with markings every 1 km. As you cross the first marker, note the odo reading and then watch until you reach the 5 km marked. Divide the...
Forum: Techniques 4 Weeks Ago
Replies: 24
Views: 1,749
Posted By erad
One problem I see with the Bog-Out is that you...

One problem I see with the Bog-Out is that you need a diff lock. If you put the Bog-Out on one front wheel, the open diff will allow the other front wheel to spin and you won't get anywhere. Another...
Forum: Electrical / Radios 4 Weeks Ago
Replies: 12
Views: 309
Posted By erad
All thermistors work the same way - the...

All thermistors work the same way - the resistance decreases as the temperature increases. The thermistor is in series with the fan motor. Thus, at low temperatures, the resistance is high and the...
Forum: Generation 3 Pajero 4 Weeks Ago
Replies: 2
Views: 280
Posted By erad
The actuator is vacuum operated, not compressed...

The actuator is vacuum operated, not compressed air. Probably the only reason for excess air would be expansion caused by heating up the air in the front diff. Check the breather.
Forum: Generation 4-1 Pajero 4 Weeks Ago
Replies: 9
Views: 558
Posted By erad
Are the globes securely mounted? If they are...

Are the globes securely mounted? If they are slightly loose, they can vibrate and this will shorten their life dramatically.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT +10. The time now is 04:00 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.