Pajero 4WD Club of Victoria Public Forum Pajero 4WD Club of Victoria Public Forum

Go Back   Pajero 4WD Club of Victoria Public Forum > Search Forums

Showing results 1 to 25 of 500
Search took 0.03 seconds.
Search: Posts Made By: Pauly Faulkner
Forum: Generation 2 Pajero 06-06-17
Replies: 91
Views: 8,724
Posted By Pauly Faulkner
As for the manual and auto. The back of block...

As for the manual and auto.
The back of block is identical including crank end. Use the adapter plate (then sheet metal plate held on by two small bolts) from the NL.

Manual you use all NL clutch...
Forum: Generation 2 Pajero 06-06-17
Replies: 91
Views: 8,724
Posted By Pauly Faulkner
Hi guys, Yes that is correct you do have to...

Hi guys,
Yes that is correct you do have to modify the engine mount a little for a comfy fit.
With no modification you are left with only a few bolts lining up and holding it in.
I will get a few...
Forum: Fuel and fuel systems 31-12-16
Replies: 4
Views: 1,072
Posted By Pauly Faulkner
Diesel has really low octane rating compared to...

Diesel has really low octane rating compared to petrol, but has a higher cetane and energy content.
Tbh I couldn't see diesel being of any benefit to a petrol motor.
Forum: Fuel and fuel systems 31-12-16
Replies: 22
Views: 2,551
Posted By Pauly Faulkner
I found 95 to be the sweet spot for me. 91 and...

I found 95 to be the sweet spot for me.
91 and e10 gave me similar economy results, 95 and 98 the engine ran noticeably smoother and better economy.
Cents per kilometre though the 91 won with 95 a...
Forum: Generation 2 Pajero 30-12-16
Replies: 4
Views: 724
Posted By Pauly Faulkner
Go with a truflow pump with backing plate, comes...

Go with a truflow pump with backing plate, comes with backing plate preassembled and with a block gasket.
Little bit dearer then a gmb pump and aftermarket backing but worth it.
Forum: Generation 2 Pajero 28-12-16
Replies: 7
Views: 588
Posted By Pauly Faulkner
That's normal, coolants thermal properties are...

That's normal, coolants thermal properties are rather weak compared to straight water. Since you don't have a thermostat in to regulate the engine temp you are over cooling and likely would of seen...
Forum: Generation 2 Pajero 28-12-16
Replies: 3
Views: 597
Posted By Pauly Faulkner
Have you got, or have you ever had a headlight...

Have you got, or have you ever had a headlight warning buzzer etc telling you you've left your headlights ON?
Normally these are wired into parkers and ignition but some people use the headlight...
Forum: Generation 2 Pajero 28-12-16
Replies: 2
Views: 621
Posted By Pauly Faulkner
Where the driver side cv bolts to diff axle, move...

Where the driver side cv bolts to diff axle, move the flange around by hand and see if there is any play in it.
Could also be the freewheel actuator on front diff trying to engage the diff which...
Forum: Generation 2 Pajero 28-12-16
Replies: 7
Views: 588
Posted By Pauly Faulkner
After the system builds pressure, the...

After the system builds pressure, the majority...if not all the bubbles will collapse. Have had a few in the past where the coolant froths at first start during bleeding and then goes away after a...
Forum: Generation 2 Pajero 28-12-16
Replies: 7
Views: 588
Posted By Pauly Faulkner
Could be a number of things but first thing comes...

Could be a number of things but first thing comes to mind due to just doing a cooling system service is cavitation and/or air pockets at the pump and since you have no thermostat in you are seeing it...
Forum: Generation 2 Pajero 28-12-16
Replies: 6
Views: 1,098
Posted By Pauly Faulkner
VMX-M for the transfer and gearbox, around...

VMX-M for the transfer and gearbox, around 2.5ltrs each.
Just use lsd oil in both diffs, saves buying a multitude of oils and there is no issues with running it in non lsd. Around 2.5ltrs rear and...
Forum: Generation 2 Pajero 28-12-16
Replies: 1
Views: 422
Posted By Pauly Faulkner
On the clutch fork pivot shaft there is a small...

On the clutch fork pivot shaft there is a small bolt at the bottom stopping the shaft sliding up and down. Remove this and also the welsh plug on the bottom of the bellhousing and slide pivot shaft...
Forum: Generation 2 Pajero 16-02-16
Replies: 3
Views: 637
Posted By Pauly Faulkner
Spot on erad. That bolt sandwiches both the...

Spot on erad.
That bolt sandwiches both the water pump and backing plate to the block, that's two gaskets through the bolt hole sealing it. Quite common for either to fall away when the bolt is...
Forum: Generation 2 Pajero 12-02-16
Replies: 42
Views: 5,432
Posted By Pauly Faulkner
Nah it's alloys and most offset steelies that...

Nah it's alloys and most offset steelies that won't fit. Even though some 15" steelies clear the rim they just have bugger all clearance so any small rocks will scratch and chew out the rim.
Forum: Generation 2 Pajero 07-02-16
Replies: 1
Views: 460
Posted By Pauly Faulkner
End freeplay in the diff. Likely excessive ring...

End freeplay in the diff. Likely excessive ring gear to pinion backlash which can be fixed but you'll need a diff/gearbox place so they can check the diff.
Forum: Generation 2 Pajero 31-01-16
Replies: 3
Views: 423
Posted By Pauly Faulkner
Yes, all gen2 dickie seats will bolt into each...

Yes, all gen2 dickie seats will bolt into each other.
Have put NL dickie seats into an NH to replace old flogged out ones before and they we're identical.
Forum: Generation 2 Pajero 31-01-16
Replies: 10
Views: 2,145
Posted By Pauly Faulkner
On thermostat housing is an overdrive inhibitor...

On thermostat housing is an overdrive inhibitor temp switch as previously mentioned. It locks out overdrive until engine temp gets above cold and this is very common to cause the no overdrive issue....
Forum: Generation 2 Pajero 31-01-16
Replies: 3
Views: 408
Posted By Pauly Faulkner
I'm guessing you are chasing the flange gasket...

I'm guessing you are chasing the flange gasket for the Y pipe to header?
If so then it's just the size you want and any exhaust shop will have them. Some auto stores stock common sizes but last time...
Forum: Generation 2 Pajero 26-01-16
Replies: 4
Views: 482
Posted By Pauly Faulkner
Fuel pump only pumps when cranking, once engine...

Fuel pump only pumps when cranking, once engine starts the ignition relay will latch ON position and keeps it ON.

Grey plug with three wires, where is it located as it sounds like crank or cam...
Forum: Generation 2 Pajero 20-01-16
Replies: 8
Views: 648
Posted By Pauly Faulkner
You can just use an aftermarket cooler and cut...

You can just use an aftermarket cooler and cut the heavy duty crimp on oil cooler line and run oil cooler hose up or just get one from the wreckers.
Will be going aftermarket with fan on my NL soon...
Forum: Generation 2 Pajero 19-01-16
Replies: 9
Views: 810
Posted By Pauly Faulkner
When standing at back of vehicle looking forward,...

When standing at back of vehicle looking forward, passenger side star wheel turns counter clockwise to tighten and driver side turns clockwise. Take note of this when refitting star wheel as it goes...
Forum: Generation 2 Pajero 19-01-16
Replies: 9
Views: 810
Posted By Pauly Faulkner
Access to star wheel is through the backing plate...

Access to star wheel is through the backing plate after you remove the small oval bung/grommet. You'll see the star wheel when you remove the rotor anyway so that will give you a good insight on how...
Forum: Generation 2 Pajero 19-01-16
Replies: 8
Views: 1,242
Posted By Pauly Faulkner
Don't forget that you need the larger caliper...

Don't forget that you need the larger caliper bracket as well to go with the rotor. Also, 15" is unlikely to fit anymore.

Preload is to make sure the outer race is seated properly in the hub. As...
Forum: Generation 2 Pajero 18-01-16
Replies: 9
Views: 810
Posted By Pauly Faulkner
Disc just slides off after removing caliper...

Disc just slides off after removing caliper bracket.
The shoes are like any other drum brake. Remove the big spring off the bottom then push and turn the small springs with lock collar and it...
Forum: Generation 2 Pajero 17-01-16
Replies: 3
Views: 586
Posted By Pauly Faulkner
Slightly different but yes, factory locker into...

Slightly different but yes, factory locker into lsd housing works.
Just remember the factory locker axles are different lengths left to right and they must be swapped over along with the centre.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT +10. The time now is 05:01 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.