Pajero 4WD Club of Victoria Public Forum Pajero 4WD Club of Victoria Public Forum

Go Back   Pajero 4WD Club of Victoria Public Forum > Members List

Pauly Faulkner Pauly Faulkner is offline

Valued Member

Visitor Messages

Showing Visitor Messages 1 to 10 of 33
  1. nermine
  2. nermine
  3. nermine
  4. Rainmann
    G'day Pauly. I just read an old post of yours pasted below, thought I'd let you know it's WD40 (CRC) , it's an old detailing trick since it's basically just fish oil, it serves two purposes nice and shiny and some rust prevention. anyway though you might like to know.

    Just don't use solvent based stuff(i.e most degreasers in a can).
    I use alkalyne degreaser like denso etc, works great.
    As for the shiny remains, i have noticed a few mechanics leave a slippery residue behind but for the life of me can't think of what it is they use. it leaves everything all glossy for a few weeks.
  5. mud boss
    mud boss
    hi pauly just wondering i done my timing belt on my nl 99 i now have this humming wyning noise at 2000 2200 rpm only what the hell can it be im going crazy my mechanic says its not the belt just let it bed in 5000klms later still there any ideas cheers
  6. Ken Salton
    Ken Salton
    hi Pauly My Names Ken just wandering if you know wether No1 cylinder is on drivers side or pass/side on my Mitsy Pajero NJ1996 no distributor just 3 coils regards Ken
  7. Old school tech
    Old school tech
    Thanks for reply pauly, I have removed RH head the one with four teeth advanced,all other timing was correct presuming if belt skipped then this cam(inlet) would be retarded four teeth belt was tight and hydraulic tensioner out to 5mm so presume previous repairer about 1k ago allowed cam to slip over TDC when installing belt,the lady owner(from new) advised me ran warmer and low power since belt replaced and finally stopped with a rattle noise.
    Result four bent inlet valves one lash adjuster broken and cam tunnels gouged,bores still have good hone pattern pistons look fine, have located sh head which will need service so that should be ok. With no experience with pajeros I am uncertain if at 275k are rings likely
    To be at end of life or do they run to 400k plus? And is there a rusty core plug at rear of block?
  8. brentanator
    hi pauly sorry to keep bugging you...i found the ticking noise and all it was is the cover that sits on the back of the gearbox that covers you unis and seal had come seems to just press on but if you push on it it just comes loose.. im guessing removing its not a good idea as it will expose the unis and seal.....would some sika flex or somthing help to hold it on.....

  9. pajeroman3lt
    Hi Pauly, do you have any 25mm body lifts? thanks Darryl
  10. Bogger
    Pauly just do $210 and I've allowed $35 for TNT (to big Aust Post) Anything different to that will sort out along the way.
    ps Empty your mail box it's full ?

About Me

  • About Pauly Faulkner
    Maitland, NSW
    Buying cold beer and taking it home and making it even colder ;)
    Make and model of vehicle.
    1997 Pajero NK LWB, 6G72 12V SOHC
  • Signature
    97' NK 3ltr GLX LWB Manual | 3" lift | Wildcat headers | K&N air filter | 2.8 crawl gears | 4Terrain clutch | 2.25" exhaust | Factory locker rear | TJM 10,000lb winch | TJM snorkel
    97' NL GLS LWB Auto | 6G75 3.8ltr | Redback Headers


Total Posts
Visitor Messages
General Information
  • Last Activity: 14-01-18
  • Join Date: 24-02-12
  • Referrals: 2


Showing Friends 1 to 10 of 22

All times are GMT +10. The time now is 09:38 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.